The purpose of this project is to design and mass-produce kits for a floating tiny house that can sail. It combines high-tech modeling and fabrication and low-tech assembly that can be carried out DIY-style on a riverbank or a beach. This boat is a 3-bedroom with a kitchen, a sauna and a dining room. The deck is big enough to throw dance parties. It can be used as a river boat, a canal boat or even a beach house. Oh, and it's rugged and stable enough to take out on the ocean. Kits will start at around $50k (USD). The design has been tested in simulation and prototype; full-scale production will begin next year.
Friday, December 2, 2016
I might do a few more towing and stability tests, to verify hull speed and initial stability angle, but we already have these numbers from the hydrostatic and hydrodynamic analysis. I don’t expect any surprises, and so there probably won’t be anything to report. I am quite happy with how boring this design has been—doing everything it’s supposed to—and I am glad that the phase of playing with models is over. I am a serious person, and I find model sailboats to be silly. They are part of due diligence, but I won’t be taking them up as a hobby.
That said, the model-building process has been incredibly useful in three separate ways.
First, I had a chance to verify our technique for joining the plywood pieces using box joins and locking tabs and slots. I did find a few problems, three of them significant. We are changing the design in light of what I discovered, and will do another test at the 1:12 scale just to make sure we got it right this time before committing to a full-scale build.
One problem had to do with the curves at the bow: the plywood panels that make up the sides and the bottom as they come together to a point at the bow cannot be cold-molded and will need to be steam-bent, which is what I did.
Another problem came up while fitting the sheer strips—the long strips with the deadlights that run all around the boat just under the deck. It is not enough to secure them in place by locking them to tabs, because that produces a scalloped profile with many small gaps. Instead, they have to be pulled into place, by applying force to them at the transom. We will design jigs for steam-bending and for sheer strip-pulling.
Also, it turned out that while box joins with a rectangular toothed profile work fine for straight segments, for curved segments the teeth have to be trapezoidal rather than rectangular, with the angle of the sides of the trapezoids proportional to the angle of curvature. This turned out to be a problem when fitting the bottom to the sides.
We also had the problem of too much joinery—too many tabs and slots. Since they are free (the slots cost something in terms of the extra machine time it takes to mill them) we used a lot of them. It turns out that too much joinery is as bad as not enough, and will now work to find a happy medium, using the minimum of joinery that still allows the entire structure to be self-aligning and self-supporting.
Another major problem I was able to solve is how to eliminate virtually all finishing work on the interior of the hull. This should make construction go much faster by eliminating interior painting. The plywood panels will be treated with penetrating epoxy prior to milling parts out of them. Interior-facing surfaces will also be sanded, primed, sanded again, and painted with very durable two-part polyurethane paint, providing a surface almost as hard as a laminate. Exterior-facing surfaces will only be sealed with epoxy, to make them waterproof, since they will receive a coat of fiberglass prior to fairing and painting. The edges of the milled panels will be left unfinished, since they will be saturated with epoxy and filleted as part of the assembly process. Where the joint is exposed, it will then be dressed up with hardwood trim, while everywhere else, such as inside lockers, it will be left as is.
But what Hassler and McLeod appear to have done in making the panels of the Junk sail rectangular is change their shape from a Lateen sail to square sail, and square sails are quite terrible upwind, tacking through no better than 60º. In theory, an airfoil can still be formed using the flex of the battens, but there are two problems with this: first, the battens flex more in stronger winds, which is the opposite of what’s needed, because the stronger the wind the flatter the sail needs to be; second, the battens flex asymmetrically depending on the tack, because on one tack the mast gets in the way.
To compensate, some people have recently decided to add camber, or “belly,” to rectangular sail panels. That was my original plan, which I thought was state of the art with regard to Junk sails. I was wrong; state of the art with regard to Junk sails is centuries-old. After I realized this, I designed a fan sail, which, as I have demonstrated yesterday, works remarkably well to windward. Here's my recipe. There are 5 panels, all fan-shaped, and 6 spars. Starting at the bottom, there is a boom, 4 battens and a gaff. All the panels are exactly the same in height at the luff and taller at the leach. The boom is horizontal, while each spar going up is angled 8º more than the previous spar, adding up to a 40º angle for the gaff.
At this point, we are able to declare QUIDNON’s design to be proven, in both digital and analog forms. It handles well under sail and motor, it is stable, stiff and steady, and, based on feedback from all the passers-by at the marina, it is pleasant to look at. We will now work on pushing the design to completion, since all that remains to work out is a very large number of relatively minor details.